I had to get rid of the extra nut and replace it with a new washer and a locking split ring washer which turned out rather nice. I use an Oettinger tailpiece on my Gibson tenor and Paramount tenors but not my Irish tenor (tuned low GDAE). The tailpiece attaches to the banjo by means of a single nut & bolt through the bottom - though it is possible to attach it with a single bolt or woodscrew through the cut-out in the back, using a suitable spacer. Banjo sound is very subjective and the Oettinger makes getting the sound you want achievable. The problem with this method is the loop can pull over to one side and the string pulls out of the groove that runs down the middle of each finger. The Deering True Toneé Tailpiece is designed to combine the best features of easy adjustment, ease of string changing, and enhance the tone of the banjo without humming. There is no adjusting mechanism on it. No! The downward pressure on the 3rd and 4th strings has been increased and the downward pressure on the 1st, 2nd and 5th strings has been reduced. So to maintain your tone you will need to readjust the tailpiece after you adjust the banjo head. Lower gives more tension which should make the banjo sound brighter and perhaps louder. The Oettinger allows the banjo player to vary the downward force of each string - in effect change the weights of the passengers in the analogy. But to accommodate the Waverly, I had to make a special modification involving shortening the distance between the lug and the pot. I dont bother. This is a waverly, a five string design, but works with four. You can shorten this process by pushing down on the Oettinger 'finger' slowly while plucking the string and you will hear the best sound from that string when the 'finger' is the right distance from the head. If the action needs to be lowered (which is usually the case), loosen the inside nut and tighten the outside nut. A general starting point on any banjo is to place the bridge the same distance away from the 12th fret as the nut is from the 12th fret. 5) Put the Presto on and adjust that bottom nut that goes into the flange so that when you pull up and lift on the tailpiece by hand its approximately the height it is in that picture posted. Step #5 â Tailpiece adjustment. Kershner "Unique" (Four Hole/Four Cam) $175.00. I tie a small looped Bowlin Knot and loop that over the 'hook' with the actual knot beneath the hook, then I pass the string back through the loop and along the finger groove. Avoid the modern no-knots, they cut through strings and some of them are impossible to tie knots to due to the cams being too close together. Position it to be aligned with the neck of the banjo, about 5 cm from the tailpiece. left, right, or in and out simply by turning the large thumb screw (for up/down adjustments) or the first and fifth string retaining screws (pivot pins) in or out as necessary (for sideways and in/out adjustments). When you tighten the tailpiece to re-connect with the tension hoop, you have now lowered the forward edge of the tailpiece closer to the head. The usual adjustment of the Oettinger tailpiece is with the treble strings having reduced downward pressure and the bass strings having increased downward pressure. It is fully adjustable. That left tension as the only variable I could adjust while actually playing, and the only tailpiece that had a mechanism to adjust tension was the Waverly; which might have given it a slight advantage over the other two. All these sort of things like hooks, t plates, l brackets, etc. Banjo Tailpiece, Banjo Tailpiece for 5 String Banjo Parts Replacement Chrome Plated Luthier Maker: Amazon.ca: Musical Instruments, Stage & Studio in essential, its a lighter version of a Kershner. space from the open 3rd string to the 19th fret on the fingerboard. Intonation is the idea of the banjo being in tune all along the fingerboard and is largely determined by the correct positioning of the bridge. Golden Gate Kershner Style Tailpiece $49.95. They aren't cheap, but I have found that Fielding tailpieces are the best modern tailpieces for nylons nowadays, and they're easy to fit on any modern banjo including the Goodtime. The tailpiece tension screw adjusts string pressure over the bridge for tonal variations. ... For more information about checking or adjusting your banjo's neck, check out the Deering article here. The bar from the tailpiece drops down through that hole and screw in the locking nut. Home Made 5 String Banjo, Low Budget Built From Parts and Some Scrap. 2. You need to bring it upright by doing the following: Loosen the strings by turning the tuning pegscounter-clockwise. Some inexpensive banjos have hooks on the banjo body that are designed to hold a strap. If the action needs raising, loosen the outside nut and tighten the inside nut. Depending on how the bridge is positioned can often be the difference between an incredible sounding banjo and a lousy one. When an arm of the Oettinger is raised, the downward force on the bridge is lowered. Thanks for using the Oettinger Tailpiece Resource. Greg Deering designed this Goodtime tailpiece to give the customer adjustability and great sound. Most people seem to attach the strings to the tailpiece as shown in the picture to the left. New style Presto banjo tailpiece has a large thumbscrew to adjust tension. Place your finger on the first string at the 12th fret without pushing it down. But one time across the 'fingers' is not enough. My banjo sounds good as before, maybe even better since the old tailpiece â¦ "The effectiveness of the Oettinger tailpiece probably varies with tuning but it often greatly improves the sound of a tenor banjo because the tuning varies so much across the strings. You can do this with almost any tail piece by canting it to one side, but this is a crude adjustment. Not sure if it's the fact that it's top tension or not. Strings will go up from the fingerboard. It uses a simple t head bolt to hold the thing down which works effectively. Eventually, each string sounds great and you are done. I got this banjo tailpiece in my shop orphaned and in a box of parts. Very slight coordinator rod adjustment can be made by ï¬rst loosening the inner and outer nuts under the tailpiece. Adjusting The Fingers Start the tuning process with the Oettinger 'finger' highest on the smallest string and lowest on the largest string. So correct bridge positioning is vital. Many players attach the strap to brackets located underneath the neck and the tailpiece of the banjo, as shown in the figure. It makes a huge difference on my Gibson.". You are now ready to set the intonation. The only way I found to control mass and length, was to swap out tailpieces. He is also the Owner/Inventor of Geiger Acoustic Devices which is well worth checking out. How Do I Set My Banjo Bridge Intonation? There are several good tailpieces on the market. The boat is very poorly trimmed in the water (on the banjo head) because the heaviest passenger is on one end and the lightest passenger is on the other end. It then loops around the top of the cam (photo 3) pulling it snug and preventing the end from slipping out (photos 4 and 5). In this video Chad Kopotic focuses on setting up a Deering True Tone tailpiece. When you hear the richest sound (indicating harmonics are strong) go to the next string and repeat this process. So my banjo is different from most models. Most require this and that to install the tailpiece. There are NO markings on this tailpiece. Adjusting the distance between the head and where the strings meet the tailpiece changes the downward tension of the strings on the bridge. Because the high pitched A string is under a great deal of tension it exerts a large downward force on the bridge. It won't when you put the strings on. However, these hooks usually arenât located in a position that provides the most comfortable support. One is the Price Straightline tailpiece. Made of solid brass with nickel plating, this tailpiece is a bit heavier than the Old Style Presto. By far the best tailpiece made today.